ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC

SummaryTHIS IS A NATIONAL GUARD TITLE 32 EXCEPTED SERVICE POSITION. This National Guard position is for a ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC, Position Description Number D1201000 and is part of the ME CSMS, National Guard.ResponsibilitiesThis position is located in the Joint Forces Headquarters-State, Logistics Directorate (J-4), Surface Maintenance Facility. The primary purpose of this position is to perform calibration, diagnostics repair, and certification of electronic, mechanical, and radiation Test Measurement and Diagnostic Equipment (TMDE). b. DUTIES AND RESPONSIBILITIES: (1) Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Aligns, troubleshoots, tests, inspects, repairs, modifies, calibrates and certifies precision measurement equipment such as multimeters, microwave equipment, oscilloscopes, temperature analyzers, mercurial barometers, gage blocks and micrometer caliper dimensional equipment, digital voltmeters, signal generators, torque wrenches, pressure gauges, torque testers, weight scales, electronic counters, radiation monitors, radix calibrators, and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions, which are often vague and incomplete, and may require the preparation of diagrams and instructions to facilitate the calibration action. (2) Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment, makes repairs, and replaces defective parts/components such as integrated circuits, printed circuit boards, electronic condition coils, radiation detector boards/circuits, crystals, transistors, tubes, transformers, condensers, diodes, relays potentiometers, and related components. (3) Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. If signal is distorted, traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls. Adjusts with trimmer potentiometers; and if calibration is still not possible, adds or removes sufficient resistance to permit balancing of circuit. As needed, contacts the using organization to obtain information concerning the nature of the malfunction. Uses equipment schematics to analyze circuits by preparing block diagram showing major components such as amplifiers, filters, oscillators and indicators. (4) Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required. Uses special test devices and radioactive samples or other calibrated sources. Tests equipment for sensitivity and correct operation. Observes necessary precautions as stipulated in operational repair manuals. Makes radiation calculations/readings at various distances from the standard ensuring radiation equipment is operating in specified parameters. Performs contamination/radiation surveys on radiation equipment to control/eliminate radiation leakage/contamination.RequirementsConditions of EmploymentQualificationsAREA OF CONSIDERATION: AREA I: All qualified permanent and indefinite Maine Army National Guard Enlisted Technicians currently assigned to CSMS who apply. Military Grades: Enlisted Compatible Military Assignments: 35T, 91F, 91G, 91X, 91Z GENERAL EXPERIENCE: Experience or training which demonstrates knowledge of equipment to be able to do routine jobs, simple preventative maintenance tasks, and is able to use common tools and equipment in the line of work. SPECIALIZED EXPERIENCE: Experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment.EducationIf you are using Education to qualify for this position, You must provide transcripts or other documentation to support your Educational claims. To receive credit for Education, you must provide documentation of proof that you meet the Education requirements for this position.Additional InformationIf you are a male applicant who was born after 12/31/1959 and are required to register under the Military Selective Service Act, the Defense Authorization Act of 1986 requires that you be registered or you are not eligible for appointment in this agency (https://www.sss.gov/RegVer/wfRegistration.aspx). If you are unable to apply online or need to fax a document you do not have in electronic form, view the following link for information regarding an Alternate Application.